Kenai Manuals
Find documentation for your Kenai water treatment system below. Need a hand programming a valve, scheduling a regeneration or troubleshooting an issue? Your Waterboy team is just a phone call away.
Point-of-Entry Systems
Whole-home softeners and filtration systems installed where water enters your home.
Salt-free scale reduction.
Manual available on request
Whole-home filtration.
Manual available on request
Smart leak monitor.
Manual available on request
Point-of-Use Systems
Drinking-water systems installed at a single tap.
UV purification.
Manual available on request
Owner's manuals for our most-requested Kenai systems are linked above. Don't see your exact model — such as the EnviroPro, Pro+Lite, StreamLabs or PureStream UV? Contact your Waterboy team and we'll send the exact documentation for your model right away.
Your Kenai water treatment system is built to run reliably for years with very little hands-on attention, but a little routine care goes a long way — especially with the hard, mineral-rich water common across Jacksonville and North Florida. The owner's manual for your specific model walks you through programming the control valve, setting the regeneration schedule, adjusting hardness settings and troubleshooting common questions. If you ever misplace your manual or buy a home with a Kenai system already installed, just reach out and we'll send the correct documentation for your exact model.
Most point-of-entry softeners and filters need nothing more than occasional salt (for systems that use it) and a periodic check of the bypass valve and settings. Salt-free and backwashing filtration systems are even lower maintenance, cleaning themselves automatically on a programmed cycle. Reverse-osmosis drinking-water systems like the FreshStream RO use replaceable twist-off cartridges and a membrane that we'll help you stay ahead of, so your drinking water always tastes its best.
Because our region draws hard water from the Floridan aquifer — often with iron and hydrogen sulfide on well supplies — your equipment works harder here than it would in many parts of the country. A few simple habits keep it performing at its best. Keep the brine tank of a salt-based softener at least one-quarter full at all times, and use a clean, high-purity salt to minimize residue and bridging. Every month or two, glance inside the brine tank to make sure salt has not formed a hard crust ("salt bridge") above the water, which can quietly stop your softener from regenerating. For iron and sulfur systems like the AirOxPro, the automatic backwash cycle does most of the work, but heavy iron loads can benefit from a periodic professional cleaning to keep the media bed fresh.
If your water suddenly tastes, smells or looks different, that is your system telling you something. A return of scale or spotting can mean a softener is low on salt or due for a setting adjustment. The return of a rotten-egg odor can indicate an iron-and-sulfur system needs service. A drop in pressure at the kitchen tap often points to a clogged RO pre-filter. None of these are cause for alarm — they are simply routine signals, and your Waterboy team can resolve most of them quickly. We also offer salt delivery, resin changes and tune-ups so you never have to think about it.
It depends on your household size, water hardness and the system you own, but most families top up the brine tank every few weeks. Your Waterboy professional will recommend a schedule, and we offer salt delivery so you never run out. Keeping the brine tank at least one-quarter full keeps your softener regenerating properly.
Each Kenai valve has an intelligent, programmable digital interface, and the steps are covered in your model's manual. If you'd rather not fuss with settings, your installer programs everything during installation based on your water test, and we're a phone call away if you need a setting changed.
Pre-filters and membranes have different lifespans depending on your water quality and usage. The FreshStream RO uses proprietary twist-off cartridges that make replacement quick and clean. We'll help you track replacement intervals so your point-of-use water stays crystal clear.
Absolutely. Waterboy services, repairs and performs resin changes on all brands of water treatment equipment across North Florida, even if you bought it elsewhere. If your current system is underperforming, we can evaluate it, tune it or recommend an upgrade.
Contact Waterboy Jax at (904) 307-1746 or Waterboy Tallahassee at (850) 464-1755, or send a message through our contact page, and we'll get you the exact documentation you need along with any guidance to keep your system delivering simply clean water.
For most homes, maintenance is light: keep salt in the brine tank for salt-based softeners, glance at your settings now and then, and replace point-of-use cartridges and RO membranes on schedule. Backwashing filtration systems clean themselves automatically. We're happy to set up reminders, deliver salt, and handle resin changes and tune-ups so you never have to think about it.
Yes. Kenai point-of-entry systems are built locally and include a Limited Lifetime Warranty, and Waterboy stands behind every installation with our money-back guarantee. If something isn't right, we'll make it right.
Keeping your manual handy and following a simple maintenance routine is the best way to protect your investment and ensure years of reliable, simply clean water. If you're ever unsure about a setting, a noise, a change in your water, or a replacement part, don't guess — reach out and let our team help you keep everything running exactly as it should.
Waterboy
